Guarded Bin Tipper




  • Stainless Steel or Mild Steel Construction
  • Food/Pharmaceutical Industry Specification
  • Standard and Custom Design Machines
  • Fully TIG/MIG Welded Construction
  • Lifts for Bins, Drums, Trays etc
  • Tip Heights up to 2500mm
  • Lifting Capacity up to 600Kgs
  • Chain or Screw Drive
  • Fully Enclosed Safety Guard
  • Fully Load Tested and CE Certified
  • LOLER Inspection and After Sales Service Available
  • Direct from a British Manufacturer

BTM/300/4450/B/G Single Pillar Guarded Bin Tipper

This Single Pillar 200 Litre Guarded Bin Tipper was designed to lift and tip at a discharge height of 4450mm. The Guarded Bin Tipper is manufactured from Grade 304 stainless steel, is a welded construction throughout and is designed to be bolted to the floor. The lifting is achieved by a ¾” Simplex chain driven by a motor gearbox mounted at the top of the main column. The Guarded Bin Tipper will be supplied with a full height safety guard as detailed below.

Safety Guard to BS EN 14120:2015 Safety of Machinery Guards

This Guarded Bin Tipper was supplied complete with a safety guard to meet the guidelines of BS EN 14120:2015 Safety of Machinery Guards. The safety guard is constructed from 40 x 40 x 3mm box section and 3mm wire, 40mm aperture stainless steel weld mesh. It encloses the Guarded Bin Tipper to a height of 2200mm above the platform height on three sides with a cut-out through which the bin is tipped on the fourth side. At the ground level there is a safety guard door through which the bins are loaded and unloaded. The guard door is electrically and mechanically interlocked preventing the Guarded Bin Tipper from operating when the door is open. Additionally, the guard door can only be opened when the lift carriage is at the full down position to prevent access whilst a load is raised.

Guarded Bin Tipper Electrical Control

This Guarded Bin Tipper is fitted with an IP65 Stainless Steel Control Panel which is mounted on the main column at a convenient position to give good maintenance access under the Provision and Use of Work Equipment Regulation 1998 (PUWER). Upper and Lower end of travel limit switches are positioned to prevent inadvertent adjustment or damage but are easily adjustable by trained personnel for fine adjustment on site.

The control panel incorporates the following controls; Up, Down, Guard Release, Emergency Stop and a Reset Facility. The Guarded Bin Tipper operation is latched so that pressing the ‘Up’ push button once will raise the lift to the full tip position. Once the product has been discharged the Guarded Bin Tipper will return to the full down position. Also included was an intermediate limit switch which paused the Guarded Bin Tipper prior to tipping if the infeed hopper was full.

Description Single Pillar Guarded Bin Tipper
Model No. BTM/300/4450/B/G
Capacity 300 Kgs
Tipping Height 4450mm
Tipping Angle 135 Degrees
Overall Height 5430mm
Machine Handing Left Hand
Maximum Headroom 6000mm
Tipping Chute No
Container Description 200 Litre Tote Bin
Base Arrangement Bolted To The Floor
Control Circuit 24Vac
Electrical Rating IP65
Limit Switches Telemecanique
Motor Detail 0.75kW, 415V, 3 PHASE, 50 CYCLE c/w BRAKE
Gearbox Detail SEW Eurodrive
Output R.P.M 28 R.P.M.
Ratio 50:1
Load/Lift/Tension Chain ¾" Simplex
Tensile Strength 3000 Kgs
Lift Speed 6.4 Meters/Minute
Application Story

You May Also Be interested In...

Customer image
300 Litre Bin Tipper
Customer image
Tote Bin Hoist
Customer image
Single Pillar Hoist
Customer image
Single Pillar Lifter
Customer image
Tray Tipper
Customer image
Column Lifter Guarded
Customer image
Guarded Trolley Tipper
Customer image
ATEX Bin Tipper
Customer image
Guarded Drum Tipper
Customer image
Guarded Bin Tipper
Customer image
Guarded Dump Buggie Tipper
Customer image
High Level Bin Tipper
Customer image
Salad Bin Tipper
Customer image
Tote Dumper High Level
Customer image
Stillage Tipper
Customer image
Guarded Tote Bin Tipper