Guarded Drum Tipper

BTM/300/1900/B/G/140

BTM/300/1900/B/G/140

Features

  • Stainless Steel or Mild Steel Construction
  • Food/Pharmaceutical Industry Specification
  • Standard and Custom Design Machines
  • Fully TIG/MIG Welded Construction
  • Lifts for Bins, Drums, Trays etc
  • Tip Heights up to 2500mm
  • Lifting Capacity up to 600Kgs
  • Chain or Screw Drive
  • Fully Enclosed Safety Guard
  • Fully Load Tested and CE Certified
  • LOLER Inspection and After Sales Service Available
  • Direct from a British Manufacturer
Description

Safety Guard to BS EN 14120:2015 Safety of Machinery Guards

This Guarded Drum Tipper was supplied complete with a safety guard to meet the guidelines of BS EN 14120:2015 Safety of Machinery Guards. The safety guard is constructed from 40 x 40 x 3mm stainless steel box section and 2.0mm stainless steel sheet. The safety guard encloses the Guarded Drum Tipper to a height of 2200mm on two sides, 1800mm on the tipping side with a hinged guard door on the fourth side. The guard door is electrically and mechanically interlocked preventing the Guarded Drum Tipper from operating when the door is open. Additionally, the guard door can only be opened when the lift carriage is at the down position to prevent access whilst a load is raised.

Guarded Drum Tipper Electrical Control

This Guarded Drum Tipper is fitted with an IP65 Stainless Steel Control Panel which is mounted on the main column at a convenient position to give good maintenance access under the Provision and Use of Work Equipment Regulation 1998 (PUWER). Upper and Lower end of travel limit switches are positioned to prevent inadvertent adjustment or damage but are easily adjustable by trained personnel for fine adjustment on site. The control panel incorporates the following controls; Up, Down, Guard Release, Emergency Stop and a Reset Facility.

The Guarded Drum Tipper operation is latched so that pressing the ‘Up’ push button once will raise the lift to the full tip position. Once the product has been discharged, pressing the ‘Down’ push button once will return the Guarded Drum Tipper to the full down position. The control panel has a volt free pair of contacts which can be used to connect a ‘Call to Run’ signal if required.

Specification
Description Single Pillar Guarded Drum Tipper
Model No. BTM/300/1900/B/G/140
Capacity 300 Kgs
Tipping Height 1900mm
Tipping Angle 140 Degrees For Tote Bins, 150 Degrees For Drums
Overall Height 3403mm
Machine Handing Right Hand
Maximum Headroom 4000mm
Tipping Chute Yes, Fitted To Lift Carriage
Base Arrangement Bolted To The Floor
Control Circuit 24Vac
Electrical Rating IP65
Limit Switches Telemecanique
Motor Detail 0.75kW, 415V, 3 PHASE, 50 CYCLE c/w BRAKE
Gearbox Detail SEW Eurodrive
Output R.P.M 28 R.P.M.
Ratio 50:1
Load/Lift/Tension Chain ¾" Duplex
Tensile Strength 6000 Kgs
Lift Speed 6.4 Meters/Minute
Application Story

You May Also Be interested In...

Customer image
300 Litre Bin Tipper
BTM/350/2850/B/G
Customer image
Tote Bin Hoist
BTM/300/2400/B/G
Customer image
Single Pillar Hoist
BTM/300/3800/B/G
Customer image
Single Pillar Lifter
BTM/350/2635/B/G
Customer image
Tray Tipper
BTM/350/1600/M/G
Customer image
Column Lifter Guarded
BTM/250/3700/B/G
Customer image
Guarded Trolley Tipper
BTM/250/2200/B/G/SL
Customer image
ATEX Bin Tipper
BTM/300/2500/M
Customer image
Guarded Drum Tipper
BTM/300/1900/B/G/140
Customer image
Guarded Bin Tipper
BTM/300/4450/B/G
Customer image
Guarded Dump Buggie Tipper
BTM/300/1854/M/G
Customer image
High Level Bin Tipper
BTM/350/4650/B/G
Customer image
Salad Bin Tipper
BTM/250/1200/B/G
Customer image
Tote Dumper High Level
BTM/100/5850/B/G
Customer image
Stillage Tipper
BTM/400/1850/B/G
Customer image
Guarded Tote Bin Tipper
BTM/300/1600/B/G