Tote Bin Hoist

BTM/300/2400/B/G

BTM/300/2400/B/G

Features

  • Stainless Steel or Mild Steel Construction
  • Food/Pharmaceutical Industry Specification
  • Standard and Custom Design Machines
  • Fully TIG/MIG Welded Construction
  • Lifts for Bins, Drums, Trays etc
  • Tip Heights up to Customers’ Requirements
  • Lifting Capacity up to 600Kgs
  • Chain or Screw Drive
  • Fully Enclosed Safety Guard
  • Fully Load Tested and CE Certified
  • LOLER Inspection and After Sales Service Available
  • Direct from a British Manufacturer
Description

BTM/300/2400/B/G Single Pillar Tote Bin Hoist

This Single Pillar 300 Litre Tote Bin Hoist is designed to lift and tip at a discharge height of 2400mm. The Tote Bin Hoist is manufactured from Grade 304 stainless steel, is a welded construction throughout and is designed to be bolted to the floor. The lifting is achieved by a ¾” Duplex chain driven by a motor gearbox mounted at the top of the main column.

Safety Guard to BS EN 14120:2015 Safety of Machinery Guards

The safety guard is a welded construction from 40 x 40 x 3mm stainless steel box section and 40mm aperture, 3.0mm wire stainless steel weld mesh and encloses the Tote Bin Hoist to a height of 2200mm on three sides, with a hinged guard door on the fourth side. The guard door is electrically and mechanically interlocked preventing the Tote Bin Hoist from operating when the door is open. Additionally, the guard door can only be opened when the lift carriage is at the full down position to prevent access whilst a load is raised.

Tote Bin Hoist Electrical Control

The Tote Bin Hoist is fitted with an IP65 Stainless Steel Control Panel which is mounted on the main column at a convenient position to give good maintenance access under the Provision and Use of Work Equipment Regulation 1998 (PUWER). Upper and Lower end of travel limit switches are positioned to prevent inadvertent adjustment or damage but are easily adjustable by trained personnel for fine adjustment on site.

The control panel incorporates the following controls; Up, Down, Guard Release, Emergency Stop and a Reset Facility. The Tote Bin Hoist operation is latched so that pressing the ‘Up’ push button once will raise the lift to the full tip position. Once the product has been discharged, pressing the ‘Down’ push button once will return the Tote Bin Hoist to the full down position. The control panel has a volt free pair of contacts which can be used to connect a ‘Call to Run’ signal if required.

Specification
Description Single Pillar Tote Bin Hoist
Model No. BTM/300/2400/B
Capacity 300 Kgs
Tipping Height 2400mm
Tipping Angle 130 Degrees
Overall Height 3550mm
Machine Handing Right Hand
Maximum Headroom 4000mm
Tipping Chute No
Container Description 300 Litre Tote Bin
Base Arrangement Base Frame Bolted To The Floor
Control Circuit 24Vac
Electrical Rating IP65
Limit Switches Telemecanique
Motor Detail 0.75kW, 415V, 3 PHASE, 50 CYCLE c/w BRAKE
Gearbox Detail SEW Eurodrive
Output R.P.M 28 R.P.M.
Ratio 50:1
Load/Lift/Tension Chain ¾" Duplex
Tensile Strength 6000 Kgs
Lift Speed 6.4 Meters/Minute
Application Story

You May Also Be interested In...

Customer image
300 Litre Bin Tipper
BTM/350/2850/B/G
Customer image
Tote Bin Hoist
BTM/300/2400/B/G
Customer image
Single Pillar Hoist
BTM/300/3800/B/G
Customer image
Single Pillar Lifter
BTM/350/2635/B/G
Customer image
Tray Tipper
BTM/350/1600/M/G
Customer image
Column Lifter Guarded
BTM/250/3700/B/G
Customer image
Guarded Trolley Tipper
BTM/250/2200/B/G/SL
Customer image
ATEX Bin Tipper
BTM/300/2500/M
Customer image
Guarded Drum Tipper
BTM/300/1900/B/G/140
Customer image
Guarded Bin Tipper
BTM/300/4450/B/G
Customer image
Guarded Dump Buggie Tipper
BTM/300/1854/M/G
Customer image
High Level Bin Tipper
BTM/350/4650/B/G
Customer image
Salad Bin Tipper
BTM/250/1200/B/G
Customer image
Tote Dumper High Level
BTM/100/5850/B/G
Customer image
Stillage Tipper
BTM/400/1850/B/G
Customer image
Guarded Tote Bin Tipper
BTM/300/1600/B/G