300 Litre Bin Tipper




  • Stainless Steel or Mild Steel Construction
  • Food/Pharmaceutical Industry Specification
  • Standard and Custom Design Machines
  • Fully TIG/MIG Welded Construction
  • Lifts for Bins, Drums, Trays etc
  • Tip Heights up to Customers’ Requirements
  • Lifting Capacity up to 600Kgs
  • Chain or Screw Drive
  • Fully Enclosed Safety Guard
  • Fully Load Tested and UKCA or CE Certified
  • LOLER Inspection and After Sales Service Available
  • Direct from a British Manufacturer

BTM/350/2850/B/G Single Pillar 300 Litre Bin Tipper

This 300 Litre Bin Tipper is designed to lift and tip at a discharge height of 2850mm into an intermediate transfer chute that will feed into the top of a mixer. The 300 litre bin tipper is constructed from Grade 304 stainless steel, is fully TIG welded throughout and is designed to be mobile on castors. The lifting is achieved by a ¾” Duplex chain driven by a motor gearbox mounted at the top of the main column.

Safety Guard to BS EN 14120:2015 Safety of Machinery Guards

The safety guard is constructed from 40 x 40 x 3mm stainless steel box section and 2.0mm stainless steel sheet to meet the requirements of BS EN 14120:2015 Safety of Machinery Guards. It encloses the 300 Litre Bin Tipper to a height of 3200mm on all sides, approximately 2800mm on the tipping side with a hinged guard door on the fourth side. The guard door is electrically and mechanically interlocked preventing the 300 litre bin tipper from operating when the door is open. Additionally, the guard door can only be opened when the lift carriage is at the full down position to prevent access whilst a load is raised.

300 Litre Bin Tipper Electrical Control

This 300 Litre Bin Tipper is fitted with an IP65 Stainless Steel Control Panel which is mounted on the main column at a convenient position to give good maintenance access under the Provision and Use of Work Equipment Regulation 1998 (PUWER). The control panel incorporates the following controls; Up, Down, Guard Release, Emergency Stop and a Reset Facility. There will be a remote push button station at the upper level with the following controls; Up, Down and Emergency Stop. The lift will rise automatically to an intermediate limit switch where control will transfer to the upper pushbutton station which will operate on a ‘dead man’s handle’ basis. The control panel has the facility for a ‘call to run’ signal to be connected if required.

Description Single Pillar 300 Litre Bin Tipper
Model No. BTM/350/2850/B/G
Capacity 350Kgs
Tipping Height 2850mm
Tipping Angle 130 Degrees
Overall Height 3915mm
Machine Handing Left Hand
Maximum Headroom 3950mm
Tipping Chute Yes, Fixed Chute Mounted Off Tipper Safety Guard
Container Description 300 Litre Tote Bin
Base Arrangement Bolted To The Floor
Control Circuit 24Vac
Electrical Rating IP65
Limit Switches Telemecanique
Motor Detail 0.75kW, 415V, 3 PHASE, 50 CYCLE c/w BRAKE
Gearbox Detail SEW Eurodrive
Output R.P.M 28 R.P.M.
Ratio 50:1
Load/Lift/Tension Chain ¾" Duplex
Tensile Strength 6000 Kgs
Lift Speed 6.4 Meters/Minute
Application Story

You May Also Be interested In...

Customer image
300 Litre Bin Tipper
Customer image
Tote Bin Hoist
Customer image
Single Pillar Hoist
Customer image
Single Pillar Lifter
Customer image
Tray Tipper
Customer image
Column Lifter Guarded
Customer image
Guarded Trolley Tipper
Customer image
ATEX Bin Tipper
Customer image
Guarded Drum Tipper
Customer image
Guarded Bin Tipper
Customer image
Guarded Dump Buggie Tipper
Customer image
High Level Bin Tipper
Customer image
Salad Bin Tipper
Customer image
Tote Dumper High Level
Customer image
Stillage Tipper
Customer image
Guarded Tote Bin Tipper
Customer image
200 Litre Tote Bin Tipper
Customer image
Dump Buggy Tipper
Customer image
Dough Tipper